I got the Vision HH for my 521L. They are good tires. Can run them at 70lbs but generally run them at 55lbs. I’ve had them for about a year and pulled them for 5000+ miles in that time. No problems.
Type: Posts; User: Grits and gravy
I got the Vision HH for my 521L. They are good tires. Can run them at 70lbs but generally run them at 55lbs. I’ve had them for about a year and pulled them for 5000+ miles in that time. No problems.
I think it might be over the weight rating for your boat depending on year.
Depends. Do you use FFS. I had a 45” and when fishing tournaments the FFS transducer would come out of the water at times. I had it as far down as possible without being on the motor housing. I went...
I had the Ultrex and replaced with the quest. I’m still not convinced it is all that much better. The mount is better but the motor itself has a slight noise when above 5 on the dial. I am also...
Mine has done the same thing. 2018 521L. When I switch power on, mine will light up but none of the buttons work and after a minute, the pad lights go out and won’t turn back on. I have been told...
Air bags. They are easy to install and total cost was about $1000 for bags and onboard inflator to control pressure. Took about 2 hours from start to finish. 10-12psi is all I need in my 2023 TRD...
The rubber boot around the steering column was squeaking on mine. I sprayed it will silicon where it rubs the mount and wheel
and fixed the squeak.
If you are really worried about it. Put a shop vac on the oil fill port as keep a vacuum on it. Then remove the drain plug and replace washer. Just make sure to not have a lot of vacuum or you will...
You could easily repair that yourself. Order the correct gel coat from Ranger and watch a YouTube video on gel repair. That would take about 1 hour total over to repair and cost about $40 for a pint...
Apply silicone sealant inside trim and use heat gun to soften the plastic trim and then reinstall.
Repower with a Yamaha 250sho and flash it to 320hp. Keep the rev limiter stock to maintain the warranty. You will get everything you are looking for. I have a 2018 521L and I’m running 70mph fully...
Looking for LVs 32 system
If you have a dremel or round file, you can use the led ones from etrailer. They are a lot
brighter and only take a minute or two to install. They are just slightly bigger and only took a couple...
If you already have a shop vac, just get a good 5gal bucket with lid and run a small plactic hose out of the lid and hook up shop vac to hole on lid of bucket. The suction will draw the oil into the...
Get the Yamaha and send the CPU to hydrotec. Leave the rev limiter stock so the warranty is still in tact. My 2018 521L is running 71-72 fully loaded with my SHO. Never had any issues at all.
The bigger boats don’t see as much top end gains. But getting out of the hole is another story. It never rises, just gets on plane as soon as I hit the throttle. My old 519 with flashed 200 was...
There is plenty of room to mount it in the standard place. The charge is much smaller than most other chargers. The 5th battery does not take up that much room.
Yamaha T2 25 pitch. I have a 2018 521L that is currently running 71-72mph. Before I changed to lithiums, it would hit 74mph. The rev limiter was left stock. Gets out of the hole great, and I usually...
With lithium there is no need to hook back up before going out. The discharge rate is so low that it won’t amount to 1-2% over a month.
Not sure it is really called a phone charger, but the 12volt plug and phone charger on my 2018 521L do not have power. I assumed it was a blown fuse but have traced the wire from the plugs to the...
Ranger parts sells them $.50 each
Xylene works better at getting the glue off than acetone. It does not evaporate as quickly and softens the glue faster. And it does not affect the gel coat.
I had a 1992 451V and it was a good boat. With a 150 it was fast. But it was small too. If you fish by yourself, it is fine, but cramped with 2 people. The price does seem high. Mine was in very...
My 2018 trailer had an issue with jumping teeth on the axle. Changed out the bolts for grade 8 and the hub that had problems bolt had stretched a tenth of an inch. Changed the bolts and no more...
I have been told there is an angle, but I measured the tire clearance on the fender before and after I reset mine. I had one that had jumped splines so I measured the good tire and then set the other...