Search:

It's an Ultrex 24v

LOL LOL Still makes me laugh !!

The clearer the water, the faster the retrieve !! They're getting to good a look at it. Rapid and erratic should do better. Try to somewhat match what the bait color is also. I know, sometimes...

I just use a Drop Shot set-up but with a very short drop line. I like to use it when the Bass are holding tight to the bottom or fishing thru sparse grass.

When I did a seat conversion from a full bench seat to 2 single seats, I had to build a seat base. I used Marine 1/2" plywood and covered it with a piece of Linoleum left over from a kitchen...

This would be much better option if the color would work. I removed a full bench seat in my 2002 205vx, built a seat base and then got the console from bassboatseats.com. But I think you could get a...

Aerator and over flow plug

I heated the plastisol in a microwave using clear 1 or 2 cup measuring cups, THEN add the color and flake. I then used the tin pouring pots, filled as many as it took for what I had heated and kept...

Going to go Lithium for my Trolling Motor, I currently run 2-12v 180Resv, sealed batteries and have never come up short at the end of the day. So, can I switch to 2-12v 50 amp/hr and make it without...

Excellent idea !!! Looking forward to the test results

https://www.amazon.com/Marinco-12VCPS3-Trolling-Motor-Receptacle/dp/B06Y5XQQNV/ref=sr_1_7?crid=3KOB62FXIEN5L&dib=eyJ2IjoiMSJ9.lQeFFPZ47IxZ2Cyz13x4WFnyMsnuJTgbKZRY5bjP5XnxfixC58JgRLt3Tz9QoOJG0EPcxlMNN-...

Is your Trolling Motor switchable for 12/24v ? The 2 battery 4-wires is for that set up. IF your trolling motor is only 12v, you can put the T/M batteries in parallel, Pos-Pos and Neg-Neg then...

NO ! The GLS10 needs power from the Battery thru a switch. The LVS34 connects to the GLS10, then the GLS10 connects thru the Network cable to the graph. But, the Graph needs it's own power supply.

He was one Funny Guy ! I listened to him many times as I drove 48 states. Didn't even mind hearing the same bit over and over, laughed every time !!! "Say WHAT" !!

Release the wench and jack the boat keel up until the keel is clear of the roller. If you have a Impact tool, spin the bolt in the remove setting while hitting the other end with a hammer. Be sure...

The HDS5 face plate comes off and exposes 4 mounting screws. There's a slot on the lower right comer that you can pry up if I remember correctly. I believe the 7 is the same. You'll need to see if...

Sounds like maybe you are overfilling it. If it stops leaking at some point and the brakes work fine, then don't add any more fluid.

That's a really old plug. I doubt you'd be able to find one. HOWEVER, that plug and receptacle needs replaced anyway. There's a lot listed on Amazon that will work.

Here's a free and easy to use program for resizing of large files.

https://pixresizer.en.softonic.com/download

OOPS, sorry, I miss understood. I change Google Earth KMZ to GPX files and then load them into the graphs

FYI, it takes 2 adaptors to connect a Garmin 12pin Echo Map to the US2 on a Ultrex. It's a IUS2 Adapter Cable / MKR-US2-14 - Garmin 8-Pin and a 8-pin Transducer to 12-pin Sounder Adapter Cable with...

I use this, it's quick and easy !

https://www.gpsvisualizer.com/

Jack the front all the way down, then use 2 jack stands and a 2x4 under the rear at the step, raise the jack stands with the 2x4 on top of them about 4-5' apart as close to the step, then raise the...

Should be 14", 5 on 4 1/2. Also, your trailer vin # is on the Trailer Registration License card.

Plus............you can just take that wheel off and just run on 3 wheel to get you home, unless it's a long way. I've run 100 miles on 3 wheels with no problems.