Results 1 to 13 of 13
  1. 03-24-2018, 11:17 AM #1
    KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    11,134

    Exclamation Pics of clean install on new Power Pole hydraulic hoses

    Pic courtesy of ELITEANGLER

    Attached Images Attached Images
    Last edited by KandKKustomz; 03-25-2018 at 08:02 AM.


    Reply With Quote Reply With Quote
  2. eliteangler
    eliteangler is offline
    Member eliteangler's Avatar
    Join Date
    Feb 2008
    Location
    Jones, OK
    Posts
    1,049
    #2 04-01-2018, 09:11 PM
    Thank you sir!! It really wasn't too hard. Just have to make sure there is nothing on the other side that the hole saw will grab or cut into (wires, hoses, etc...).
    Sam Dunaway
    2005 Triton TR-21X
    Powered by Suzuki 250SS
    Reply With Quote Reply With Quote
  3. Nitro_Z20
    Nitro_Z20 is offline
    Member
    Join Date
    Jun 2017
    Location
    Missouri
    Posts
    179
    #3 04-18-2018, 05:41 PM
    Attached Images Attached Images
    2023 Nitro Z21 XL Pro
    2023 Pro XS 250
    Lowrance Ghost
    Lowrance HDS 12 Live
    Lowrance HDS 12 Live
    Dual CM2 8' Blades

    Tow Vehicle
    2022 GMC AT4 3500 HD Crew Cab Duramax
    2008 Dodge Ram 3500 6.7 Cummins
    Reply With Quote Reply With Quote
  4. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    11,134
    #4 04-26-2018, 08:19 PM
    looks good!


    Reply With Quote Reply With Quote
  5. eliteangler
    eliteangler is offline
    Member eliteangler's Avatar
    Join Date
    Feb 2008
    Location
    Jones, OK
    Posts
    1,049
    #5 04-29-2018, 12:16 PM
    That is very clean!!
    Sam Dunaway
    2005 Triton TR-21X
    Powered by Suzuki 250SS
    Reply With Quote Reply With Quote
  6. ckaihara
    ckaihara is offline
    Member
    Join Date
    Dec 2012
    Location
    Little Mountain , SC
    Posts
    142
    #6 07-29-2018, 02:35 PM
    How did you do that? Do the new 2.0 poles come with those rubber grommets?
    Reply With Quote Reply With Quote
  7. eliteangler
    eliteangler is offline
    Member eliteangler's Avatar
    Join Date
    Feb 2008
    Location
    Jones, OK
    Posts
    1,049
    #7 07-29-2018, 10:37 PM
    Quote Originally Posted by ckaihara View Post
    How did you do that? Do the new 2.0 poles come with those rubber grommets?
    Yes. They do. I used a hole saw when I did mine. The install instructions will tell you what size to use.
    Sam Dunaway
    2005 Triton TR-21X
    Powered by Suzuki 250SS
    Reply With Quote Reply With Quote
  8. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    11,134
    #8 08-06-2018, 08:11 PM
    Quote Originally Posted by ckaihara View Post
    How did you do that? Do the new 2.0 poles come with those rubber grommets?
    sure do!


    Reply With Quote Reply With Quote
  9. SteezMacQueen
    SteezMacQueen is offline
    Member
    Join Date
    Aug 2017
    Location
    North Texas
    Posts
    1,121
    #9 12-27-2018, 07:11 PM
    Quote Originally Posted by eliteangler View Post
    Yes. They do. I used a hole saw when I did mine. The install instructions will tell you what size to use.
    Takes a 3/4” hole. I used a cheap step but from harbor freight. I started mine with a 1/8” pilot hole. Then the step bit. Also, use a liberal amount of silicon to seal both the hoses to the grommets and the grommets to the hull. Allow to cure for 24hours before getting them wet.
    Reply With Quote Reply With Quote
  10. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    11,134
    #10 12-27-2018, 07:39 PM
    Quote Originally Posted by SteezMacQueen View Post
    Takes a 3/4” hole. I used a cheap step but from harbor freight. I started mine with a 1/8” pilot hole. Then the step bit. Also, use a liberal amount of silicon to seal both the hoses to the grommets and the grommets to the hull. Allow to cure for 24hours before getting them wet.
    When drilling thru fiberglass always be sure to run your drill in reverse first to start the hole then switch to forward


    Reply With Quote Reply With Quote
  11. tracer1
    tracer1 is offline
    tracer1 tracer1's Avatar
    Join Date
    Jun 2013
    Location
    Aiken, SC
    Posts
    2,393
    #11 07-22-2019, 12:28 PM
    Where can you get the grommets for the 5/16" plastic hoses?
    Reply With Quote Reply With Quote
  12. KandKKustomz
    KandKKustomz is offline
    BBC SPONSOR/ Shallow Water Anchors Moderator
    Join Date
    Apr 2015
    Location
    New York
    Posts
    11,134
    #12 07-23-2019, 11:27 AM
    Quote Originally Posted by tracer1 View Post
    Where can you get the grommets for the 5/16" plastic hoses?
    call Power Pole most likely will send them to you no charge! would be the plastic inserts for the older 5/16" line not grommets like the 2.0 hoses have however


    Reply With Quote Reply With Quote
  13. Bmdubya
    Bmdubya is offline
    Member
    Join Date
    Sep 2016
    Location
    Greenville SC
    Posts
    57
    #13 08-01-2022, 10:03 AM
    Listened to my dealer, and for a phoenix boat I think this location makes sense. No kinks and easy to route inside the box.

    20220801_134131101 (2).jpg
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »